40% OFF SITE-WIDE + EXTRA 10% OFF USWS BRANDED SYSTEMS | COUPON: FALL
Mon-Fri 8am - 8pm | Sat 9am-3pm EDT
Se habla español
SHOP McAfee SECURE sites help keep you safe from identity theft, credit card fraud, spyware, spam, viruses and online scams
Mon-Fri 8am - 8pm | Sat 9am-3pm EDT

Axeon TF RO Membranes

Axeon Residential TF Series RO Membrane Elements

 

TF Series RO Membrane Elements

Recognized as one of the industry’s most reliable and highest performing membrane elements which deliver consistent quality and performance. Advanced membrane film technology and manufacturing processes allow these elements to deliver consistent results that water treatment equipment suppliers, distributors and dealers have come to rely on.
  • 98% Nominal Salt Rejection
  • Improved System Performance
  • Superior Quality and Cost Savings
  • Individually Tested and Sanitized
  • Made in the U.S.A.


TF (Thin Film Composite)
reverse osmosis membrane elements offer reliability, high performance, and deliver consistent results for higher quality water.

Operating Limits:

  • Membrane Type:  Thin Film Composite
  • Maximum Operating Temperature:  110ºF (43ºC)
  • Maximum Operating Pressure: 125 PSI
  • Maximum Feed Flow Rate: 1 GPM
  • Minimum Concentrate Flow Rate: 4xPermeate
  • pH Range, Continuous Operation:  3 - 11
  • Maximum Feed Water Turbidity: 1 NTU
  • Maximum Feed Silt Density Index (SDI): 5 SDI
  • Chlorine Tolerance: 0 PPM
Product Specifications
 Part Number
 Description  Applied Pressure PSI (BAR)
Permeate Flow Rate GPD
Nominal Salt Rejection (%)
200357 USWM-1812-25 50 (3.45) 25 98
200358 USWM-1812-35 50 (3.45) 35 98
200359 USWM-1812-50 50 (3.45) 50 98
200360 USWM-1812-75 50 (3.45) 75 98
200361 USWM-1812-100 50 (3.45) 100 98
200362 USWM-1812-150 50 (3.45) 150 98

Permeate flow and salt rejection based on the following test conditions: 550 ppm Softened Tap Water, 77°F (25°C), 15% Permeate Recovery, 6.5 – 7.0 pH Range, and the specified applied pressure. Data taken after 30 minutes of operation. Maximum pressure drop for each element is 10 psi. Minimum salt rejection is 96%. Permeate flow for individual elements may vary +/- 20%.

Dimensions (inches)
Description A B C D E
TF-1512-12N 11.740 0.860 0.930 1.775 10.000
TF-1512-18N 11.740 0.860 0.930 1.775 10.000
TF-1512-25N 11.740 0.860 0.930 1.775 10.000
TF-1512-35N 11.740 0.860 0.930 1.775 10.000
TF-1512-50N 11.740 0.860 0.930 1.775 10.000
TF-1512-75N 11.740 0.860 0.930 1.775 10.000
TF-1512-100N 11.740 0.860 0.930 1.775 10.000
TF-1512-150N 11.740 0.860 0.930 1.775 10.000

Wet tested membrane elements must be kept sealed and moist when in storage. Drying out may occur and damage the membrane permanently. Prevent elements from freezing or being exposed to direct sunlight. Wet tested elements are vacuum sealed in a polyethylene bag containing 1.0% sodium meta-bisulfite and then packaged in a cardboard box. Discard the permeate for the first two hours of operation. The permeate flow (product water flow) varies with feed water temperature. Review a Temperature Correction Chart. For membrane warranty information, please contact manufacturer.